LTC2600IUFD#PBF【PDF 6/20 页】IC DAC OCTAL R-R 16BIT 20-QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录2006

2页 3页 4页 5页 [6页]7页 8页 9页 10页

LTC2600/LTC2610/LTC2620

2600fe

OPERATION

Power-Down Mode

For power-constrained applications, power-down mode

can be used to reduce the supply current whenever less

than eight outputs are needed. When in power-down, the

buffer ampliers and reference inputs are disabled, and

draw essentially zero current. The DAC outputs are put

into a high impedance state, and the output pins are pas-

sively pulled to ground through individual 90k resistors.

When all eight DACs are powered down, the master bias

generation circuit is also disabled. Input- and DAC-register

contents are not disturbed during power-down.

Any channel or combination of channels can be put into

power-down mode by using command 0100b in combi-

nation with the appropriate DAC address, (n). The 16-bit

data word is ignored. The supply and reference currents

are reduced by approximately 1/8 for each DAC powered

down; the effective resistance at REF (Pin 6) rises accord-

ingly, becoming a high impedance input (typically > 1GΩ)

when all eight DACs are powered down.

Normal operation can be resumed by executing any

command which includes a DAC update, as shown in

Table 1. The selected DAC is powered up as its voltage

output is updated.

There is an initial delay as the DAC powers up before it

begins its usual settling behavior. If less than eight DACs

are in a powered-down state prior to the update command,

the power-up delay is 5μs. If, on the other hand, all eight

DACs are powered down, then the master bias genera-

tion circuit is also disabled and must be restarted. In this

case, the power-up delay is greater: 12μs for VCC = 5V,

30μs for VCC = 3V.

Voltage Outputs

Each of the 8 rail-to-rail ampliers contained in these parts

has guaranteed load regulation when sourcing or sinking

up to 15mA at 5V (7.5mA at 3V).

Load regulation is a measure of the amplier’s ability to

maintain the rated voltage accuracy over a wide range of

load conditions. The measured change in output voltage

per milliampere of forced load current change is expressed

in LSB/mA.

DC output impedance is equivalent to load regulation, and

may be derived from it by simply calculating a change in

units from LSB/mA to Ohms. The ampliers’ DC output

impedance is 0.025Ω when driving a load well away from

the rails.

When drawing a load current from either rail, the output

voltage headroom with respect to that rail is limited by

the 25Ω typical channel resistance of the output devices;

e.g., when sinking 1mA, the minimum output voltage =

25Ω 1mA = 25mV. See the graph Headroom at Rails vs

Output Current in the Typical Performance Characteristics

section.

The ampliers are stable driving capacitive loads of up

to 1000pF.

Board Layout

The excellent load regulation and DC crosstalk performance

of these devices is achieved in part by keeping “signal”

and “power” grounds separated internally and by reducing

shared internal resistance to just 0.005Ω.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

相关代理商/技术参数

LTC2600IUFD#TRPBF 功能描述:IC DAC OCTAL R-R 16BIT 20-QFN RoHS:是类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装封装/外壳:28-LCC（J 形引线）供应商设备封装:28-PLCC（11.51x11.51）包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极采样率（每秒）:143k

LTC2601CDD 功能描述:IC DAC 16BIT SGL R-R VOUT 10DFN RoHS:否类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:14-WFDFN 裸露焊盘供应商设备封装:14-DFN-EP（4x3）包装:管件输出数目和类型:8 电压，单极采样率（每秒）:*

LTC2601CDD#PBF 功能描述:IC DAC 16BIT SGL R-R VOUT 10DFN RoHS:是类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行转换器数目:2 电压电源:单电源功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）供应商设备封装:8-uMAX 包装:管件输出数目和类型:2 电压，单极采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF)

LTC2601CDD#TR 功能描述:IC DAC 16BIT SGL R-R VOUT 10DFN RoHS:否类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:14-WFDFN 裸露焊盘供应商设备封装:14-DFN-EP（4x3）包装:管件输出数目和类型:8 电压，单极采样率（每秒）:*

LTC2601CDD#TRPBF 功能描述:IC DAC 16BIT SGL R-R VOUT 10DFN RoHS:是类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:14-WFDFN 裸露焊盘供应商设备封装:14-DFN-EP（4x3）包装:管件输出数目和类型:8 电压，单极采样率（每秒）:*

LTC2601CDD-1#PBF 功能描述:IC DAC 16BIT R-R 10-DFN RoHS:是类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行转换器数目:2 电压电源:单电源功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）供应商设备封装:8-uMAX 包装:管件输出数目和类型:2 电压，单极采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF)

LTC2601CDD-1#TRPBF 功能描述:IC DAC 16BIT SGL R-R VOUT 10DFN RoHS:是类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行转换器数目:3 电压电源:模拟和数字功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:*

LTC2601IDD 功能描述:IC DAC 16BIT SGL R-R VOUT 10DFN RoHS:否类别:集成电路 (IC) >> 数据采集 - 数模转换器系列:- 产品培训模块:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色产品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 标准包装:91 系列:- 设置时间:4µs 位数:10 数据接口:MICROWIRE?，串行，SPI? 转换器数目:8 电压电源:单电源功率耗散（最大）:2.7mW 工作温度:-40°C ~ 85°C 安装类型:表面贴装封装/外壳:14-WFDFN 裸露焊盘供应商设备封装:14-DFN-EP（4x3）包装:管件输出数目和类型:8 电压，单极采样率（每秒）:*

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式